BootROM - 1.73 Booting from NAND flash General initialization - Version: 1.0.0 Detected Device ID 6810 High speed PHY - Version: 2.0 Init RD NAS topology board SerDes lanes topology details: | Lane # | Speed | Type | -------------------------------- | 0 | 06 | SATA0 | | 1 | 05 | USB3 HOST0 | | 2 | 06 | SATA1 | | 5 | 05 | USB3 HOST1 | -------------------------------- High speed PHY - Ended Successfully DDR3 Training Sequence - Ver TIP-1.26.0 mvSysEnvGetTopologyUpdateInfo: TWSI Read failed DDR3 Training Sequence - Switching XBAR Window to FastPath Window DDR3 Training Sequence - Ended Successfully Not detected suspend to RAM indication BootROM: Image checksum verification PASSED __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** U-Boot 2013.01-svn48023 (Oct 13 2015 - 09:25:56) Marvell version: 2014_T3.0p6 Board: RD-NAS-88F6820-DDR3 SoC: MV88F6810 Rev A0 running 1 CPUs CPU: ARM Cortex A9 MPCore (Rev 1) LE CPU 0 CPU @ 1332 [MHz] L2 @ 666 [MHz] TClock @ 250 [MHz] DDR @ 666 [MHz] DDR 32 Bit Width, FastPath Memory Access, DLB Enabled, ECC Disabled DRAM: 512 MiB Map: Code: 0x1fed0000:0x1ff95d60 BSS: 0x1ffef2b4 Stack: 0x1f9cff20 Heap: 0x1f9d0000:0x1fed0000 U-Boot Environment: 0x00200000:0x00280000 (NAND) NAND: 256 MiB MMC: mv_sdh: 0 *** Booting kernel from kernel 2 @0x08700000 *** USB2.0 0: Host Mode USB3.0 0: Host Mode USB3.0 1: Host Mode Board configuration detected: Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x01 | egiga0 [PRIME] Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x8700000, size 0xf00000 15728640 bytes read: OK * kernel: cmdline image address = 0x02000000 Starting kernel ... Power on HDD1 ... Power on HDD2 ... Power on USB ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpuset Initializing cgroup subsys cpuacct Linux version 3.10.39 (root@uk.vultr) (gcc version 4.8.5 20150209 (prerelease) (crosstool-NG 1.21.0) ) #11 Sun May 22 12:51:05 UTC 2016 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Marvell Armada 380/381/382/385/388 (Device Tree), model: Marvell Armada 380 STG-328 Memory policy: ECC disabled, Data cache writealloc CPU: All CPU(s) started in SVC mode. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyS0,115200 root=LABEL=rootfs PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512MB = 512MB total Memory: 504324k/504324k available, 19964k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc082a034 (8329 kB) .init : 0xc082b000 - 0xc0e5a1ac (6333 kB) .data : 0xc0e5c000 - 0xc0eb4e20 ( 356 kB) .bss : 0xc0eb4e20 - 0xc0f03f70 ( 317 kB) NR_IRQS:16 nr_irqs:16 16 LSP version: linux-3.10.39-2014_T3.0p7 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B Console: colour dummy device 80x30 Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 Initializing cgroup subsys debug Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys blkio CPU: Testing write buffer coherency: ok Setting up static identity map for 0xc0647b10 - 0xc0647b68 mvebu-pmsu: Initializing Power Management Service Unit Initializing CPU Reset module devtmpfs: initialized mvebu-soc-id: MVEBU SoC ID=0x6810, Rev=0x4 xor: measuring software checksum speed arm4regs : 2368.000 MB/sec 8regs : 1458.800 MB/sec 32regs : 1408.000 MB/sec xor: using function: arm4regs (2368.000 MB/sec) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations irq: Cannot allocate irq_descs @ IRQ194, assuming pre-allocated irq: Cannot allocate irq_descs @ IRQ226, assuming pre-allocated bio: create slab at 0 raid6: int32x1 203 MB/s raid6: int32x2 270 MB/s raid6: int32x4 283 MB/s raid6: int32x8 323 MB/s raid6: using algorithm int32x8 (323 MB/s) raid6: using intx1 recovery algorithm gpio-ms: gpio_dev = fe00000 (M: 254, m: 0) [kernel] gpio_request for GPIO[24] failed with error number: -517 [kernel] gpio_request for GPIO[31] failed with error number: -517 [kernel] gpio_request for GPIO[44] failed with error number: -517 mvebu-pcie pcie-controller.3: PCIe0.0: link down mvebu-pcie pcie-controller.3: PCIe1.0: link down mvebu-pcie pcie-controller.3: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe8000000] pci_bus 0000:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers enabled PCI: bus2: Fast back to back transfers enabled pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:02.0: PCI bridge to [bus 02] PCI: enabling device 0000:00:01.0 (0140 -> 0143) PCI: enabling device 0000:00:02.0 (0140 -> 0143) vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered cfg80211: Calling CRDA to update world regulatory domain Switching to clocksource armada_370_xp_clocksource NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@monad.swb.de). fuse init (API version 7.22) bio: create slab at 1 Btrfs loaded msgmni has been set to 985 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver ****** turn off all LEDs that turned on in u-boot ****** ****** blink SYS LED ****** mv_xor f1060800.xor: Marvell shared XOR driver mv_xor f1060800.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060800.xor: freeing 1 in use descriptors! mv_xor f1060800.xor: Marvell XOR: ( crc32c ) mv_xor f1060900.xor: Marvell shared XOR driver mv_xor f1060900.xor: Marvell XOR: ( xor cpy intr ) mv_xor f1060900.xor: freeing 1 in use descriptors! mv_xor f1060900.xor: Marvell XOR: ( crc32c ) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A console [ttyS0] enabled brd: module loaded loop: module loaded ahci_mv f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs scsi0 : ahci_mv_platform scsi1 : ahci_mv_platform ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58 ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58 armada-nand f10d0000.nand: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC NAND device: Manufacturer ID: 0xc2, Chip ID: 0xda (Macronix NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 nand_read_bbt: bad block at 0x00000e920000 7 ofpart partitions found on MTD device armada-nand Creating 7 MTD partitions on "armada-nand": 0x000000000000-0x000000200000 : "U-Boot" 0x000000200000-0x000000400000 : "U-Boot env" 0x000000400000-0x000000e00000 : "Config" 0x000000e00000-0x000001d00000 : "Kernel-1" 0x000001d00000-0x000008700000 : "RootFS-1" 0x000008700000-0x000009600000 : "Kernel-2" 0x000009600000-0x000010000000 : "RootFS-2" m25p80 spi0.0: unrecognized JEDEC id ffffff SoC: model = 0x6810, revision = 0x4 o 3 Giga ports supported o SKB recycle supported (Disabled) o NETA acceleration mode 1 o RX Queue support: 8 Queues * 256 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled port #0: is_sgmii=0, is_rgmii=1, phy_addr=1 o Loading network interface(s) for port #0: cpu_mask=0x1, tx_csum_limit=9800 o Port 0 is connected to Linux netdevice o eth0, ifindex = 2, GbE port = 0 giga p=0: mtu=1500, mac=00:00:00:00:00:00 (platform) libphy: orion_mdio_bus: probed e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI e1000: Copyright (c) 1999-2006 Intel Corporation. e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k e1000e: Copyright(c) 1999 - 2013 Intel Corporation. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-orion: EHCI orion driver orion-ehci f1058000.usb: EHCI Host Controller orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1 orion-ehci f1058000.usb: irq 50, io mem 0xf1058000 orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 3.10.39 ehci_hcd usb usb1: SerialNumber: f1058000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2 xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 3.10.39 xhci-hcd usb usb2: SerialNumber: f10f0000.usb3 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd f10f0000.usb3: xHCI Host Controller xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3 usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: xHCI Host Controller usb usb3: Manufacturer: Linux 3.10.39 xhci-hcd usb usb3: SerialNumber: f10f0000.usb3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4 xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000 usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: xHCI Host Controller usb usb4: Manufacturer: Linux 3.10.39 xhci-hcd usb usb4: SerialNumber: f10f8000.usb3 ata2: SATA link down (SStatus 0 SControl 300) ata1: SATA link down (SStatus 0 SControl 300) hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected xhci-hcd f10f8000.usb3: xHCI Host Controller xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5 usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: xHCI Host Controller usb usb5: Manufacturer: Linux 3.10.39 xhci-hcd usb usb5: SerialNumber: f10f8000.usb3 hub 5-0:1.0: USB hub found hub 5-0:1.0: 1 port detected usbcore: registered new interface driver usblp usbcore: registered new interface driver usb-storage mousedev: PS/2 mouse device common for all mice mvebu-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0 i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com dm_crypt using the OCF package. cpuidle: using governor ladder sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA sdhci-pltfm: SDHCI platform and OF driver helper armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2 armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: int_coalescing(1) armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources threshold 0x2, threshold_time 0xff mvCesaInit: channels=2, session=640, queue=256 armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode cesadev_init(c0845178) usb 1-1: new high-speed USB device number 2 using orion-ehci usbcore: registered new interface driver usbhid usbhid: USB HID core driver TCP: cubic registered NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 mvebu-rtc f10a3800.rtc: setting system clock to 2016-05-22 16:21:30 UTC (1463934090) Warning: unable to open an initial console. Freeing unused kernel memory: 6332K (c082b000 - c0e5a000) systemd-udevd[1176]: starting version 229 usb 1-1: New USB device found, idVendor=090c, idProduct=1000 usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1: Product: DISK 2.0 usb 1-1: Manufacturer: USB usb 1-1: SerialNumber: 8M5L72SFMU8JQP96 usb-storage 1-1:1.0: USB Mass Storage device detected scsi2 : usb-storage 1-1:1.0 scsi 2:0:0:0: Direct-Access USB DISK 2.0 1219 PQ: 0 ANSI: 0 CCS sd 2:0:0:0: Attached scsi generic sg0 type 0 sd 2:0:0:0: [sda] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 2:0:0:0: [sda] No Caching mode page found sd 2:0:0:0: [sda] Assuming drive cache: write through sd 2:0:0:0: [sda] Attached SCSI removable disk EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem EXT4-fs (sda1): mounted filesystem without journal. Opts: (null) systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +A) systemd[1]: Detected architecture arm. Welcome to Ubuntu 16.04 LTS! systemd[1]: Set hostname to . systemd[1]: Reached target Swap. [ OK ] Reached target Swap. systemd[1]: Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems (Pre). systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. systemd[1]: Reached target User and Group Name Lookups. [ OK ] Reached target User and Group Name Lookups. systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. systemd[1]: Started Read required files in advance. [ OK ] Started Read required files in advance. systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... systemd[1]: Starting Nameserver information manager... Starting Nameserver information manager... systemd[1]: Starting Create list of required static device nodes for the current kernel... Starting Create list of required st... nodes for the current kernel... systemd[1]: Starting Uncomplicated firewall... Starting Uncomplicated firewall... systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. systemd[1]: Starting Journal Service... Starting Journal Service... systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. systemd[1]: Mounting Debug File System... Mounting Debug File System... systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. systemd[1]: Reached target Slices. [ OK ] Reached target Slices. systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. systemd[1]: Listening on fsck to fsckd communication Socket. [ OK ] Listening on fsck to fsckd communication Socket. systemd[1]: Reached target Encrypted Volumes. [ OK ] Reached target Encrypted Volumes. systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. systemd[1]: Mounted Debug File System. [ OK ] Mounted Debug File System. systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Started Load Kernel Modules. [ OK ] Started Create list of required sta...ce nodes for the current kernel. [ OK ] Started Uncomplicated firewall. [ OK ] Started Nameserver information manager. Starting Create Static Device Nodes in /dev... Mounting FUSE Control File System... Starting Apply Kernel Variables... [ OK ] Mounted FUSE Control File System. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Apply Kernel Variables. Starting udev Kernel Device Manager... [ OK ] Started udev Kernel Device Manager. Starting Remount Root and Kernel File Systems... [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Reached target Local File Systems (Pre). Starting udev Coldplug all Devices... [ OK ] Reached target Local File Systems. Starting Set console keymap... Starting Tell Plymouth To Write Out Runtime Data... Starting LSB: AppArmor initialization... Starting Load/Save Random Seed... Starting Flush Journal to Persistent Storage... [ OK ] Started Tell Plymouth To Write Out Runtime Data. [ OK ] Started Load/Save Random Seed. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started LSB: AppArmor initialization. [ OK ] Started Set console keymap. Starting Raise network interfaces... Starting Create Volatile Files and Directories... [ OK ] Started udev Coldplug all Devices. [ OK ] Found device /dev/ttyS0. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... Starting Network Time Synchronization... [ OK ] Started Network Time Synchronization. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Reached target System Initialization. [ OK ] Started Trigger resolvconf update for networkd DNS. [ OK ] Reached target Paths. [ OK ] Started Daily Cleanup of Temporary Directories. pool #0: pkt_size=1536, buf_size=1600 - 4096 of 4096 buffers added [ OK ] Listening on UUID daemon activation socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting LSB: daemon to balance interrupts for SMP systems... [ OK ] Started Regular background program processing daemon. Starting System Logging Service... Starting Initialize hardware monitoring sensors... Starting Accounts Service... [ OK ] Started D-Bus System Message Bus. Starting Permit User Sessions... Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"... Starting Login Service... [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt activities. [ OK ] Reached target Timers. [ OK ] Started ifup for eth0. [ OK ] Started System Logging Service. [ OK ] Started Permit User Sessions. [ OK ] Started Initialize hardware monitoring sensors. [ OK ] Started LSB: daemon to balance interrupts for SMP systems. [ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand". [ OK ] Started Raise network interfaces. [ OK ] Started Accounts Service. [ OK ] Started Login Service. [ OK ] Reached target Network. Starting OpenBSD Secure Shell server... Starting /etc/rc.local Compatibility... [ OK ] Started /etc/rc.local Compatibility. Starting Terminate Plymouth Boot Screen... Starting Hold until boot process finishes up... [ OK ] Started Terminate Plymouth Boot Screen. [ OK ] Started Hold until boot process finishes up. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Reached target Login Prompts. [ OK ] Started OpenBSD Secure Shell server. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. [ OK ] Started Stop ureadahead data collection 45s after completed startup. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Ubuntu 16.04 LTS nas326 ttyS0 nas326 login: